Table of Contents
Overview
...
- Research room and study room locks are changed the first week of September.
- This ensures the batteries are freshest during our busiest time of year, beginning of Fall term.
- Staff areas and the loading dock locks are also changed in September which means every electronic lock should have the batteries changed during the first week of September.
Annual Summer Unlock
Every summer we use the Smart Time feature to set the 5th floor study rooms to automatically unlock during the day.
...
Patrons are not required to reserve 5th floor study rooms or check out the key card at the Circulation desk during the summer.
...
At the end of summer intersession, the locks are set to automatically lock again.
...
Battery Replacement
CM Series lock (old locks)
Supplies
- Check-off form
- Philips head screwdriver or cordless drill
- 4 AA batteries per lock
- Study Rooms Master key
Steps to replace batteries
- The battery compartment is located under the interior latch, secured by four Philips head screws, one at each corner.
- Remove all 4 screws while carefully holding on to the back of the lock so it doesn't fall.
- Carefully pull the piece off of the door.
- This is most easily done with the door closed.
- When you do this, you are locking yourself in the room. Don't freak out.
- The piece you are removing will look like this.
- The part remaining on the door will have a square hole that should have a peg with a spring on it. Sometimes the peg will fall out. Some of the doors are missing the spring.When you put it back in, make sure the rounded end is outward facing.
- Remove the old batteries and replace with new ones.
- Fit the back panel back, being careful to line up the peg and spring. Then replace the screws.
- Take care to sink the screws properly; if you don't, the threads inside the panel will be stripped and the screw will not screw in completely. It may also cause damage to the panel.
- A good trick is to put the screw in by hand, turn it counter-clockwise until you feel the screw slip into place. Then carefully turn the screw clockwise by hand a rotation or two to properly thread the screw.
- Finally, pull on the handle to make sure that the latch engages. If it doesn't, remove the back panel again and check whether the batteries and the spring and pin are in correctly.
- Record completion of door.
- When all doors have been completed, record in table at the bottom of this page.
Battery replacement for CO-200 & AD-200 locks (new locks)
These locks need to be changed more often, probably twice per year.
Supplies
...
Important steps to remember when programming for Summer Unlock:
- Verify building hours for summer before setting SmarTime
- Start time is when the library opens for the day and End time is 15 minutes after the library closes for the day.
- There will be a separate profile for Mondays-Thursdays, Fridays, Saturdays, and Sundays depending on the summer schedule.
Battery Replacement
You should gather the supplies listed below when replacing batteries, especially if you are doing multiple locks.
- Check-off form (found in Box>Library Maintenance>Electronic Locks
- Philips head screwdriver with PH#1 (For LE Locks)
- Philips head screwdriver with PH#2 (For CO/AD Locks)
- 4 AA batteries per lock
- Master Key card for New locks
...
- key
CO-200 & AD-200 locks
- The battery compartment is located under the interior latch, secured by one Philips head screw.
...
- After unscrewing, remove the cover to expose the battery pack. The cover needs to be pulled Remove one of the side screws on the band holding the battery pack in place. Then pull the cover down and out.
- After unscrewing, remove the cover to expose the battery pack. The cover needs to be pulled down and out.
...
- Put everything back together and replace screw by hand tightening. Avoid over tightening the screws.
- Record completion of door.
- When all doors have been completed, record in table at the bottom of this page.
Lock Maintenance
...
LE Locks
- Remove the single screw at the top of the battery cover on the backside of the lock. You will need a #1 Phillips head screwdriver for this because the screws are very small.
- Replace the four batteries
- Screw the battery cover back into place.
Documentation
It is important to maintain documentation including spec files, operator manuals, purchasing and maintenance records, etc. for the electronic locks. These will be useful when troubleshooting problems.